Fastel Adhesive Products

Toll Free 1-888-989-3832 (US Only) +1-949-369-7676 (Intl)

heat activated adhesive film, hot melt, thermal bonding adhesive sealing, die cut adhesive, gasket
heat activated adhesive, die cut adhesive, thermal bonding film, adhesive sealant, pre-formed adhesive, glue, thermally applied adhesive
High Performance Thermal Bonding Adhesive and Sealing Films

Standard FastelFilm Phase-Change Temperatures

FastelFilm 15066 (150oF / 66oC)
FastelFilm 16071 (160oF / 71oC)
FastelFilm 20093 (200oF / 93oC)
FastelFilm 230110 (230oF / 110oC)

Note: custom phase-change temperature formulations available.
Document
Click Here to Download the FastelFilm Data Sheet
FastelFilm Preliminary Surface Tack Options
FastelFilm LT
- Light Tack Temporary Surface Placement (1 side)
FastelFilm HT - High Tack Temporary Surface Placement (1 side)
Note: Preliminary tack options available for all FastelFilm Temperatures and Film Thicknesses.  Ideal for material positioning and placement before heating

FastelFilm Color Options

Translucent / Yellow Tint (Standard)
Black (infrared heating)
Gray

Note: custom FastelFilm coloring available 
FastelFilm Adhesive is a specially formulated thermal bonding film available in a range of phase-change (melt point) temperatures and free standing film thicknesses.  FastelFilm is designed to adhere strongly to a wide range of substrates which makes it an ideal solution for many industries including electronics assembly, automotive, industrial, alternative energy as well as medical device application.

As a dry-to-the-touch free standing adhesive film, FastelFilm can be die cut to match a wide range of mounting and sealing applicaiton areas.  Applications can vary from bonding and/or sealing fasteners or contacts, components, adhering materials for lamination, case sealing or difficult areas of general device assembly where liquid adhesives can run-out.  As a die cut adhesive pad, FastelFilm allows for quick and clean "drop-in-place" installation/setup and instantly ready to be heat cured above its phase-change temperature using a wide range of thermal induction methods.  Once allowed to cool below its phase-change temperature, the adhesive is cured.

FastelFilm Product Features

* Uniform Bond Line Adhesion/Sealing
* Multiple Phase-Change Temperatures
* Various Film Thicknesses
* Die Cuts, Sheets Rolls


* Excellent Adhesion to Substrates
* Controlled Flow When Heated
* Re-Workable After First Cure
* Quick Installation and Fixturing

* Low Cost Adhesive Solutions
* Indefinite Shelf Life
* Solvent Free / Acid Free
* Short Lead Times

FastelFilm Standard Thicknesses (Free Standing Film)

1 Mil
(0.001", 0.03mm)
3 Mil (0.003", 0.08mm)
5 Mil (0.005", 0.13mm)
10 Mil (0.010", 0.25mm)
15 Mil (0.015", 0.38mm)
30 Mil (0.030", 0.76mm)

Note: custom film thicknesses available.  For more information, e-mail info@fasteladhesives.com or contact toll free 1-888-989-3832 (US) or +1-949-369-7676 (International)


FastelFilm Adhesive Delivery Options

Die Cut Pad (Individuals)
Die Cut Pad (Continuous Rolls)
Log Rolls or Sheets

FastelFilm Product Film / Coating Options

Free Standing Adhesive Film
Coated Aluminum, Copper or Stainless
Coated PET, PE, Polyimide Film
100% Substrate Surface Coating or Masked Coating
About FasteFilm

FastelFilm is an EVA based solvent free (environmentally friendly) adhesive film that is designed to provide uniform adhesion and sealing across a desired material interface.   The ability to manufacture FastelFilm in a variety of phase-change temperatures, film thicknesses, roll, sheet sizes and pre-form die cuts allows us to meet a wide range of requirements within multiple industries.   FastelFilm's inherent flexibility from manufacturing to installation makes it an ideal solution for applications ranging from low volume (even prototypes) and/or high volume environments.   FastelFilm is manfuactured to superior guidelines set forth by our ISO 9001:2008 Quality Standards and offers a quick turnkey solution from design to production.
FastelFilm Heat Curing Methods

All FastelFilm Phase-Change Formulations can be heat cured using commercially available heating devices.   When cycled past its phase-change temperature, FastelFilm will begin its controlled flow filling in any microscopic surface imperfections as well as adjust for any flatness condtions that may exist across your material interface.

Recommended heating devices include a curing oven, heated press, hydraulic press, heated roller(s), heated flat plate, heat tunnel, heat gun or custom fixture/heating device.

Download the FastelFilm Data Sheet above for more information on recommended setups and heat cycling times.
Want to cure FastelFilm alongside other heat curing materials?

Not a problem with FastelFilm.  FastelFilm Adhesive can by cycled higher than its recommended application temperatures for long periods of time if being cured alongside other heat required materials/adhesives that require longer cycling times in a curing oven.

Popular FastelFilm Applications 

Electronics Application
Fastener/Contact Bonding and Sealing
Component / Surface Mounting
Frame Assembly
Display Assembly
Case Bonding and Sealing
Fixture/Assembly Setup
Membrane Switch Assembly
Automotive Application
Fastener/Contact Bonding and Sealing
Plastic Lens Bonding and Sealing
Fabric/Interior Assembly
Component Mounting
Membrane Switch Assembly
Fixture/Assembly Setup
Glass Bonding
Alternative Energy Application
Photovoltaic Cell Bonding/Sealing
Fastener/Contact Bonding and Sealing
Surface Mounting
Component Mounting
Solar Device Assembly
Fixture/Assembly Setup
Glass Bonding
Laminations
Flooring/Wood Laminating
Plastic Film Laminating
Foil Layer Laminating
Paper Layer Laminating
Fabric Layer Laminating
Glass Bonding
Medical Device Application
Fastener/Contact Bonding and Sealing
Component Mounting
Display Mounting/Sealing
Fixture/Assembly Setup
Packaging Application
Package Bonding and Sealing
Labeling
Fixture/Assembly Setup
Heat Seal Foils Available (click here)
FastelFilm Coated Substrate Options

In addition to manufacturing a free standing film, all FastelFilm Formulations have the ability to be coated at specific thicknesses on a wide range of substrate types designed to meet a specific requirement.

Masking Options:  FastelFilm Adhesive masking options is a process in which the substrate is masked before applying the adhesive coating.   The masking is then removed to allow for exposed areas of the substrate.  Popular for copper substrates where exposure of substrate in predetermined areas is desired for electrical contact or soldering.
 
For more information on substrate coated materials or masking options, please contact us toll free at 1-888-989-3832 (US) or +1-949-369-7676 (International) or e-mail info@fasteladhesives.com
Common Substrate Coated Materials

Metal Foils
* Aluminum 1100, 1235
* Copper 101, 110
* Stainless 304, 321
* Brass
* Inconel

Plastics & Rubbers
* PET Film
* Heat Stabilized PET
* Polyimide Films
* Foams (Various Durometers)
* Rubber (Various Types)

Other
* Synethic Substrates
* Laminates
* Customer Defined Substrates

More Information and Samples

Adhesive material evaluation is always critical when designing in a new material or developing a new product.  Sheet samples or FastelFilm Adhesive are available for preliminary review and testing to determine the optimal FastelFilm formulation, thickness, setup and heating method within the scope of your application requirements.

Click Here to Request More Information or Samples

Want to Test Samples First Per Your Required Outline?

Our razor plotter sampling machine allows us to provide our customers FastelFilm already cut to their required outline for testing.  Plotter formed samples provide our customers the ability to test not only the adhesive, but their required outline as well without incurring the expensive of production tooling.  The ability to plotter cut samples is dependent on the required customer die cut outline needed.   For more information to see if your required die cut can be plottered first for sampling, please e-mail info@fasteladhesives.com


Contact Us

Contact Fastel Adhesives and Substrate Products toll free at 1-888-989-3832 (US), +1-949-369-7676 (International) or e-mail info@fasteladhesives.com for questions, more information or to request product samples.
 
Click Here to Request More Information or Samples
FastelFilm is a trademark of Fastel Adhesive Products
Patent Pending